Tag: palladium

Posted on by

Ammonia electrosynthesis in a palladium membrane flow cell

Fertilizer granules

Ammonia (NH₃) is a crucial raw material for fertilizer production and a potential renewable, carbon-free energy storage solution. It is produced in the Haber-Bosch process using natural gas (CH4). During this process, natural gas is converted into hydrogen (H₂) and CO₂ by steam reforming. The Haber-Bosch process accounts for approximately 1-3% of global CO₂ emissions. This method requires stable energy supply and CAPEX intensive facilities, leading to highly centralized ammonia production. In contrast, alternative electrochemical pathways for ammonia production represent sustainable and decentralized solutions.

Electrochemical ammonia production is not a new process and is based on hydrogen electrolysis. In a subsequent step, hydrogen is used for catalytic nitrogen reduction. Experimentally, lithium and calcium have been used as electrocatalysts. Ammonia has been produced in continuous flow cells with efficiencies of up to 76%, as well as in other electrochemical cells. However, stable ammonia production in flow cells requires dry and purified hydrogen.

The primary issue with moist hydrogen is the excessive formation of lithium hydroxide (LiOH):

2 Li + 2 H₂O → 2 LiOH + H₂

However, water electrolysis could be completely eliminated if the protons (H+) generated from water oxidation were directly supplied to the lithium-coated cathode. This would further simplify systems and lower investment costs.

Researchers at Imperial College London followed exactly that approach. They coupled continuous water oxidation directly to lithium-mediated nitrogen reduction under non-aqueous conditions in a two-chamber flow cell. They recently published their results in the journal ACS Energy Letters.

The coupling was achieved through an electrically isolated, hydrogen-permeable palladium membrane between the chambers. On the anodic side (aqueous), water was oxidized at an iridium oxide-coated titanium anode to produce protons, meaning adsorbed H. This form of hydrogen permeated the palladium membrane. It then entered the dry, non-aqueous cathodic chamber, where N₂ was reduced on lithium.

Schematic palladium membrane ammonia synthesis

The palladium membrane was not integrated into the external circuit during nitrogen reduction. It simultaneously served as both a proton source and sink, made possible by its electrical conductivity and hydrogen permeability.

The scientists first validated proton transport through the palladium membrane while preventing water crossover through symmetric cell tests and ¹H-NMR isotopic exchange using water (H₂O) and deuterium oxide (D₂O, heavy water).

Real-time mass spectrometry of D₂O at the anode confirmed that deuterons supplied through the palladium membrane were incorporated into ammonia (ND₂H). This demonstrates that the protons in NH₃ originated from water oxidation and not solely from the ethanol used as well. It was evidence for linear charge transfer while maintaining negligible water transport.

As a control, an experiment was conducted using a Nafion™ membrane to demonstrate that membranes allowing water crossover prevented lithium-mediated ammonia synthesis. Nafion™ permits proton transfer while being permeable to water.

The researchers showed that the electrical conductivity of the palladium membrane enabled it to operate simultaneously as both an anode and a cathode. This allowed for continuous conversion of nitrogen and water into ammonia without producing molecular hydrogen as an intermediate. The Nafion™ control proved that the transport of protons while preventing water crossover allowed for lithium-mediated ammonia synthesis.

The necessity for pre-hydration of the membrane and the gradual increase in membrane potential during pulsed operation indicated that the kinetics of hydrogen transfer and membrane stability were key factors for performance. This was because the system was optimized for the neutral aqueous electrolyte with isotopic labeling. The researchers proposed ways to improve efficiency in their article, including the exploration of alternative hydrogen-permeable metals and alloys.

The presented membrane could find applications beyond ammonia synthesis, in other electrochemical transformations where anhydrous conditions and controlled proton release are required. These include CO₂ reduction and non-aqueous redox flow batteries.

For further research, the authors suggested:

  • Increase proton flow and reduce membrane transition resistance,
  • Test alternative hydrogen-permeable metals or alloys to reduce costs, and
  • Conduct pulse and idle protocols to monitor lithium loss.

At Frontis Energy, we are eager to see how individual monolithic palladium membranes will enter in the market. Continuous ammonia electrosynthesis represents a conceptual advancement towards simpler, more robust green fertilizer production and energy storage.

Ye et al. 2026, Continuous ammonia electrosynthesis from nitrogen and water in a monolithic Pd membrane-based flow cell, ACS Energy Letters, DOI: 10.1021/acsenergylett.5c03617

Image: Pixabay

Posted on by

Improving direct ethanol fuel cells by fluorine doping

Direct ethanol fuel cells (DEFCs) are fuel cells that run on ethanol to directly produce electrical power. Despite having much to offer they have not been forayed into. Ethanol can be made from biomass by yeasts and its oxidation products – CO2 and H2O – are hence environmentally friendly. The application of DEFCs could be a lucrative solution for vehicles due to the energy efficiency if mass-produced. Our current infrastructure for combustion fuels is ready for ethanol. DEFC usage would therefore be a sustainable and environment-friendly alternative to current internal combustion engines. Moreover, ethanol is liquid, which facilitates distribution, storage and use.

According to studies sponsored by  International Energy Agency (IEA), DEFCs deliver high power densities, culminating between 50 to 185 mW / cm2. Currently, DEFCs face multiple challenges such as slow redox kinetics, limited performance, and the high cost of electrocatalysts needed for DEFCs.

In a DEFC, the two key reactions are:

  1. Ethanol Oxidation Reaction (EOR)
  2. Oxygen Reduction Reaction (ORR)

Their sluggish rates have prevented widespread adoption of this technology. State-of-the-art DEFCs require expensive platinum-based materials to catalyze these reactions. Yet, they do not completely oxidize ethanol to CO2 to complete the EOR reaction, limiting the energy efficiency. One way to fix this issue is to separate and re-inject the unreacted ethanol. Since this adds more engineering to the fuel cell, a better solution is to find more efficient catalysts. Hence, to realize the true potential of DEFCs, is to find cheaper and more active catalysts for the two reactions in DEFCs.

The researchers at the University of Central Florida and their colleagues experimented on Pd–N–C catalyst and attempted to improve catalyst performance by introducing fluorine atoms. The team used alkaline membranes and platinum-free catalysts. Not only were these more cost-effective but also produced a high power output.

Previous research on electrocatalytic systems revealed that the local coordination environment (LCE) of the electrode surface is pivotal in tuning the activity of electrocatalysts made of carbon-supported metal nanoparticles. The study showed that introducing fluorine atoms in Pd–N–C catalysts regulated the LCE around the Pd, improving both activity and durability for the two key reactions. This improved the catalytic performance, and ultimately the fuel cell’s performance.

The new study demonstrated that fluorine doping rearranged the electron structure of the fuel cell catalyst. This substantially improved power density and ultimately the performance of the DEFC when compared with present-day benchmark catalysts. The experimental results on long-term stability demonstrated promising advancements towards practical applications of such catalysts in DEFCs.

Results

Upon experimental analysis, it was found that the fluorine atoms in the catalyst weakened carbon-nitrogen bond and pushed the N atoms towards palladium. This electron translocation efficiently regulated the LCE of palladium by forming palladium-nitrogen active sites for catalytic reactions.

The N-rich palladium surface promoted carbon-carbon bond cleavage and enabled complete ethanol oxidation. During the ORR, the N-rich palladium surface surface not only weakened CO2 adsorption but also created more accessible catalytic sites for rapid O2 adsorption.

According to the authors, a commonly occurring problem in DEFCs – the inability to complete the two key reactions – has been resolved. Their catalyst enhanced the overall performance of the fuel cell. The addition of fluorine also enhanced the durability of the catalyst by reducing the corrosion of carbon materials as well as inhibiting palladium migration and aggregation.

When the novel catalyst was tested in a DEFC, an output maximum power density of 0.57 W/cm2 was obtained. The fuel cell was stable for more than 5,900 hours. The proposed strategy, when experimented with using other carbon-supported metal catalysts, also gave improved results in activity and stability.

Outlook

The main shortcoming of DEFCs running in the alkaline condition is their durability. Currently, it is not sufficient for practical applications. Moreover, the anion-exchange membranes in use have two issues:

  • Structural stability of membrane is insufficient for long-term use
  • Carbonation occurs in presence of CO2 due to its reaction with hydroxide ions, ultimately degrading the catalyst.

Albeit stable for remarkable 5,900 hours, the membrane was replaced after 1,200 hours in the presented study. Since replacing membranes require complete disassembly of the cell, this is not a long-term practical solution.

Hence, there must be further research on increasing ionic conductivity and stability of anionic membranes for practical use of DEFC in alkaline conditions. Ideally, the hydroxide solution used to increase ionic conductivity is avoided to preserve energy density and reduce the complexity of the device. Solid oxide fuel cells offer a solution for these problems since the fuel is oxidized in gaseous form but their ceramic membrane are too fragile for mobile applications.

The current experiment makes significant strides in improving power density in DEFCs much more than any state-of-the-art DEFCs. The way ahead is further research to overcome these smaller obstacles in the long-term use of anionic membranes.

Experimental analysis

Materials used

Commercial Pd/C (10%, 8 nm Pd particles on activated carbon), as well as Pt/C (20%, 3 nm Pt particles on carbon black), were used as baseline catalysts. Also, Nafion™ solution (5%), carbon paper (TGP-H-060), and anion-exchange membranes (Fumasep FAS-PET-75)

Synthesis of heteroatom X-doped carbon (X–C, X=N, P, S, B, F)

Carbon black with abundant oxygen functional groups and melamine (C3H6N6) were mixed and ground, and finally pyrolyzed. After cooling to room temperature, N–C was obtained by washing with ethanol and water. The same method was used to synthesize P–C, S–C, B–C, and F–C from sodium hypophosphite anhydrous, sulfur powder, boric acid, and polyvinylidene difluoride.

Synthesis of hetero-atom fluorine-doped carbon catalysts

N–C and polyvinylidene difluoride were mixed and ground before adding them into a solution of acetone and water. After ultra sound treatment, the mixture was refluxed in an oil bath until fully dried. The mixture was then pyrolyzed and after cooling to room temperature, the samples were washed with ethanol and ultrapure water, followed by a vacuum to obtain the fluorinated catalyst support. The same method was used for the other precursors.

A microwave reduction method was used to synthesize palladium catalyst on the catalyst support. The content of palladium in all samples was kept at 1.0%, which was determined and double-confirmed by X-ray spectroscopy and inductively coupled plasma.

Electrochemical characterizations

For the electrical measurements, either a glassy carbon ring-disc electrode or rotating ring-disc electrode were used. The Fumasep membrane was used as an anion-exchange membrane, modified to change it to a hydroxide environment.

Reference

Chang et al., 2021, Improving Pd–N–C fuel cell electrocatalysts through fluorination-driven rearrangements of local coordination environment. Nature Energy 6, 1144–1153 https://doi.org/10.1038/s41560-021-00940-4

Image Source: P_Wei, Pixabay

Posted on by

Highly durable platinum-palladium-based alloy electrocatalyst for PEM fuel cells

To decrease the consumption of fossil fuel-derived energy for transportation, proton exchange membrane fuel cells (PEMFCs) are one of the most promising clean power sources. Their performance, however, strongly depends on the efficiency and durability of the electrocatalyst used for the hydrogen and oxygen reactions occurring at the electrodes. Noble metals such as platinum and gold are still considered as the most efficient catalysts. At the same time, their high cost and scarcity are major road blocks for scale commercialization of these energy devices.

Various solutions of catalyst design are intensively investigated in order to make this technology economically successful. Searching for high catalyst activity and durability for fuel cells is in focus of current research and development. To date, state-of-the-art electrocatalysts are based on carbon materials with varying platinum loadings.

Ultra-high active platinum group metal (PGM) alloy catalyst

Although, recent research reported ultra-high activity of some metal alloy catalysts, problems still remain. Some of these issues are related to utilization of high atomic percentages of PGM (sometimes up to 75% Pt), poor durability and performance under industrial conditions. In search for new solutions, researchers of the State University of New York at Binghamton, USA, and their collaborators reported a new design in journal Nature Communication: a highly-durable alloy catalyst was obtained by alloying platinum and palladium at less than 50% with 3d-transition metals (Cu, Ni or Co) in ternary compositions.

They addressed the problem of severe de-alloying of conventional alloy catalysts under the operating conditions, resulting in declining performance. For the first time, dynamic re-alloying as a way to self-healing catalysts under realistic operating conditions has been demonstrated to improve fuel cell durability.

Alloy combination and composition

The wet-chemical method was used for synthesis of Pt20PdnCu80−n alloy nanoparticles with the desired platinum, palladium and copper percentages. The selected set of ternary alloy nanoparticles with tunable alloy combinations and compositions, contained a total content of platinum and palladium of less than 50%, keeping it lower than current PGM-based alloy catalysts. The incorporation of palladium into platinum nanomaterials enabled a lower degree of de-alloying and therefore better stability. Additionally, palladium is a good metal partner to platinum due to their catalytic synergy and their resistance to acid corrosion.

To reduce the need for platinum and palladium core catalysts, a third, non-noble transition metal played a central role in the catalytic synergy of alloying formation. Non-noble metals such as copper, cobalt, nickel or similar were used. The platinum-palladium alloy with base metals allowed the researchers to fine tune the thermodynamic stability of the catalysts.

Morphology and phase structure

The thermochemical treatment of carbon-supported nanoparticles was crucial for the structural optimization. The metal atoms in the catalytic nanoparticles were loosely packed with an expanded lattice constant. The oxidative and reductive treatments of the platinum-palladium alloy (PGM <50%) allowed a thermodynamically stable state in terms of alloying, re-alloying and lattice strains. The re-alloying process not only homogenized the inhomogeneous composition by inter-diffusion upon calcination of nanoparticles, but also provided an effective pathway for self-healing following de-alloying.

Single face-centered cubic type structures were observed in Pt20PdnCu80–n nanoparticles (n = 20, 40, 60, 80) nanoalloys. Copper-doping of platinum-palladium alloys reduced the lattice constant effectively, as shown by high energy X-ray diffraction. Maximized compressive strain and maximized activity of the Pt20Pd20Cu60 catalyst confirmed strong correlation between the lattice constants and the oxygen reduction activity.

The researchers demonstrated that the thermodynamically-stable Pt20Pd20Cu60/C catalyst exhibited not only the largest compressive strain after 20,000 cycles, but also high activity and high durability. The discovery that the alloy catalyst remains alloyed under fuel cell operating condition is in sharp contrast to the fully de-alloyed or phase-segregated platinum skin or platinum shell catalysts reported in almost all current literature.

The significance in understanding of the thermodynamic stability of the catalyst system is a potential paradigm shift of design, preparation, and processing of alloy electrocatalysts.

(Photo: Pixabay)