Posted on

Production of Green Hydrogen through exposure of nano particles to sunlight

The demand for energy is increasing and raw material for the fossil fuel economy is diminishing. Moreover, the emission of gases from fossil fuel usage significantly degrades air quality. The carbon by-products produced from these fossil fuels severely affect the climate.

Hence, there is a need to find a renewable energy resource, that can be produced, stored, and used easily as per requirement. Hydrogen can be a promising energy resource as it is an abundantly available, non-toxic resource, and can be readily used to store excess electrical energy.

Hydrogen when combined with oxygen in a fuel cell produces electricity and the by-products obtained are water and heat. Based on the method of production of hydrogen it is categorized as blue hydrogen and green hydrogen. Blue hydrogen is produced from fossil fuels such as methane, gasoline, coal while green hydrogen is produced from non-fossil fuels / water. The cleanest way to produce eco-friendly hydrogen is via electrolysis of water where water is electrolyzed to separate hydrogen and oxygen. Renewable energy can be used as a power electrolyzer to produce hydrogen from water. Solar driven photo electrochemical (PEC) water splitting is one of the common method used these days. In photo electrochemical (PEC) water splitting, hydrogen is produced from water using sunlight.

PEC cells comprise of a working photoelectrode and a counter electrode. The photoelectrode consists of semiconductor material with a band gap to absorb solar light and generate an electron-hole pair. The photo-generated charges are responsible for the oxidation of water and its reduction into hydrogen. The PEC suffer devices from low stability and efficiency.

The research team from the  Institut national de la recherche scientifique (INRS) along with researchers from the Institute of Chemistry and Processes for Energy, Environment and Health (ICPEES) , a CNRS-University of Strasbourg joint research lab published a way to significantly improve the efficiency of water dissociation to produce hydrogen by the development of sunlight photosensitive-nanostructured electrodes.

A comparative study between cobalt and nickel oxide nanoparticles deposited onto TiO 2 nanotubes prepared through anodization was carried out. The TiO 2 nanotubes were decorated with CoO (cobalt oxide) and NiO (nickel oxide) nanoparticles using the reactive pulsed laser deposition method. The surface loadings of CoO or NiO nanoparticles were controlled by the number of laser ablation pulses. The efficiency of CoO and NiO nanoparticles as co-catalysts for photo-electrochemical water splitting was studied by cyclic voltammetry, under both simulated sunlight and visible light illuminations and by external quantum efficiency measurements

The entire research work was carried out in the following steps:

Catalyzed Green Hydrogen synthesis
Steps followed to improve the efficiency of hydrogen production

(Source: Favet et al ., Solar Energy Materials and Solar Cells , 2020)

In this study Cobalt (CoO) and Nickel (NiO) oxides were considered as effective co-catalysts for splitting water molecules. Both co-catalysts improved photo-electrochemical conversion of ultra violet as well visible light photons.

However, CoO nanoparticles were found to be the best co-catalyst under visible light illumination, with a Photo Conversion Efficiency almost 10 times higher than for TiO 2 . The performance of CoO nanoparticles got enhanced in the visible spectral region (λ> 400 nm). The possible reason can be a consequence of their visible bandgap which enables them to harvest more photon in the 400-500 nm range and transferring effectively the photo-generated electrons to TiO 2 nanotubes.

At Frontis Energy we are exited about these new discovery to improve hydrogen production from sunlight and hope to see an industrial application soon.

(Image: Engineersforum)

Reference: Favet et al ., Solar Energy Materials and Solar Cells , 2020

Posted on

Microbial Power-to-Gas in exhausted oilfields as bridge between renewable and fossil energy

An abandoned or unproductive oilfield can be reused for methane production from CO2 using renew­able electrical power. Exhausted oilfields can be reactors for the conversion of renewable energy to natural gas using microbes. To achieve this, an oilfield can be made electrically conductive and catalytically active to produce natural gas from re­newable power sources. The use of natural gas is superior to any battery because of the existing infra­structure, the use in combustion engines, the high energy density and because it can be recycled from CO2. Oil­fields are superior to any on-ground production because of the enormous storage capaci­ties. They are already well explored and these geological formations underwent environmental risk assessments. Lastly, the microbial power-to-gas technology is already available.

Process summary

Whole process (end-to-end via methane)

50% electrical efficiency

Energy density of methane

180 kWh kg1

Storage capacity per oilfield

3 GWh day1

Charge/Discharge cycles

Unlimited

Investment (electrodes, for high densities)

$51,000 MW1

Cost per kWh (>5,000 hours anode lifetime)

<$0.01 kWh1

Electrolyte

Seawater

The Problem

To address the problem of storing renewable energy, batteries have been proposed as a possible so­lution. Lithium ion batteries have a maximum energy storage capacity of 0.3 kWh kg−1. To date, this is consid­ered the best trade-off between cost and efficiency but these batteries are still too inefficient to replace gasoline, which has a capacity of about 13 kWh kg−1. This makes battery driven cars heavier than conventional cars. Lithium air batteries are considered a possible al­ternative because they can reach theoretical capacities of 12 kWh kg−1 but technical difficulties have prevented them from being used for transportation.

In contrast, methane has an energy density of 52 MJ kg−1 corresponding to 180 kWh kg−1 which is sec­ond only to hydrogen with 500 kWh kg−1, not counting in nuclear energy. This high energy den­sity of methane and other hydrocarbons along with their facile usage, is the reason why they are used in combustion and jet engines that drive nearly all transportation to date. While electrical cars seem to be a tempting green alternative, the fact that combustion engines and the fueling infrastructure are so wide-spread makes it difficult to switch.

In addition to the difficulty of changing habits, battery-driven electrical cars need other limited natural resources such as lithium. To equip all 94 million automobiles produced worldwide in 2017, 3 mega tons lithium carbonate would need to be mined annually⁠. This is nearly 10% of the entire recoverable lithium resources of 35 mega tons worldwide. Although lithium and other met­als can be recycled, it is clear that metal based batteries alone will not build the bridge between green en­ergy and tradi­tional ways of transportation due to the low energy densities of metals. And this does not even take into account other energy de­mands such as industrial nitrogen fixation, aviation or heating.

For Germany, with its high proportion of renewable energy, fuel for cars is not the only problem. As re­newable energy is generated in the north, but many energy consumers are in the south, the grid ca­pacity is frequently reached during peak production hours. A steadier energy output can only be ac­complished by decentralizing the production or by en­ergy storage. To decentralize production, home­owners were en­couraged to equip their property with solar panels or wind­mills. As tax incentives phase out, homeowners face the prob­lem of energy storage. The best product for this group of cus­tomers so far are again lithium ion batteries but investment costs of $0.10 kWh−1 are still unattractive espe­cially be­cause these products store the en­ergy as electricity which can only be used for a short time and is less efficient than natural gas when used for heating.

Natural gas is widely used as energy source today and the global energy infrastructure is designed for natural gas and other fossil fuels. Increasing demand and lim­ited resources for these fossil fuels were the main driv­ers of oil and gas prices during the last years, slowed by the recent economic crises and hydraulic fractur­ing (fracking). The high oil price attracted in­vestors to recover oil using techniques that be­come in­creasingly expensive and are environmental risks such as deep-sea drilling or tar sand extraction. Ironically, the high oil price made costly renew­able ener­gies an economically feasible alterna­tive and helped driving down their cost. Since habits are difficult to change and building an entirely new infrastructure only for renewable energies does not seem economically feasible today while CO2 drives global warming, a more realistic solution needs to be found.

Microbial Power-to-Gas could be a bridging technology that integrates renewable energy into the existing fossil fuel in­frastructure. It reaches break even in less than 2 years if certain preconditions are met. This is ac­complished by integrating methane produced from renewable energy into the current oil and gas pro­ducing infrastructure. The principal idea is to use carbon instead of metals as energy carrier because of its high energy density when bound to hydrogen. The benefits are:

  • High energy density of 180 kWh kg−1 methane
  • Low investments due to existing infrastructure (natural gas, oilfield equipment)
  • Carbon is not a limited resource
  • Low CO2 footprint due to CO2 recycling
  • Methane is a transportation fuel
  • Methane is the energy carrier for the Haber-Bosch process
  • Inexpensive catalysts further reduce initial investments
  • Low temperatures due to bio-catalysis
  • No toxic compounds used
  • No additional environmental burden because existing oilfields are reused

The solution

Methane can be synthesized by microbes or chemically. Naturally, methane is produced by anaerobic (oxygen-free) microbial biomass decomposition. The energy for biomass synthesis is provided by sun­light or chemical energy like hydrogen. In the case of methanogens (methane producing microbes), energy is harvested after CO2 and hydrogen were re­leased from biomass de­composition following a 1-to-4 stoichiometry:

CO2 + 4 H2 → CH4 + 2 H2O

Without microbes, methane is produced by the Nobel-prize winning Sabatier reaction and several attempts are currently underway to use it on industrial scale. It is necessary to split water into hydrogen and use this to re­duce CO2 in the gas phase. A major drawback of the Sabatier reaction is the need for high tempera­tures around 385ºC, and a nickel catalyst that becomes quickly spent. Methanogens use iron-nickel enzymes called hydro­genases to harvest energy from hydrogen, but do so at ambient tempera­tures.

To produce abiotic hydrogen, water is split using precious metal catalysts. Microbes split water using hydrogenases in reverse direction and the produced hydro­gen is oxidized by methanogens that grow in the electrolyte or on electrodes to pro­duce methane⁠. This reaction oc­curs at the correct 1-to-4 stoichiometry⁠ at potentials that are near to the theoretical hydro­gen production potential of −410 mV obtained from the Nernst equation in neutral aqueous solu­tions⁠. Methanogenic microorganisms are able to reduce the overpoten­tial.

Power-to-Gas concept for exhausted oilfields. Electrolysis catalyzes water splitting inside the oilfield producing methane gas and O2.

The future challenge will be to accelerate methane production rates as has been reported for a high tem­perature oilfield cul­tures⁠. Besides increasing the temperature, the most obvious solution is to use a higher reactive surface and bringing both electrodes closer together. Using carbon brushes that are poor hydrogen catalysts but provide a higher sur­face for microbial attachment is one possibility. Methane production correlates with microbial cell numbers in the reactors.

The number of methanogens in microbial electrolysis reactors correlates with the electrode surface.

To overcome the problem of expensive carbon (and also steel) brushes for large scale applications,exhausted gas and oilfields could be used. They provide a high surface area and are usually eco­nomic liabili­ties and not assets. Methano­gens inhabit oilfields where they carry out the final step in anaero­bic petroleum degradation⁠. Hence, oilfields can be seen as bioreactors at geological scale. Geological formations provide ideal con­ditions for produc­ing, storing and ex­tracting methane.

Open questions and potential solutions

Oilfield porespace volume

The Californian Summerland oilfield, for instance, has been abandoned and extensively studied in the past. It produced 27 billion barrels of oil and 2.8 billion m3 methane during its lifetime of 90 years. This maximum load of 3.5 billion m3 left the same volume of porespace filled with seawater behind. Only 2% of these pores are larger than 50 µm, which is necessary for microbial growth assuming dimensions of 1 x 2 µm of a methanogen cell. Experiments showed that the resulting 70 million m3 accessible porespace have a storage capacity of 35,000 TW.  That is a lot of methane assuming a solubility of 0.74 kg methane m−3 seawater at 500 m water depth⁠. All German off-shore windfarms together have a capacity of 7,000 MW. Obviously, the limiting factor is not the volumet­ric storage capacity of an oilfield.

Microbial methane production rates

But how fast can microbes produce methane in an hypothetical oilfield? Under optimal conditions, methanogens that grow on electrodes (typically the genus Methanobacterium or Methanobrevibacter) can produce methane at a rate of 100-200 nmol ml−1 day−1 (equals 2.24-4.48 ml l−1 day−1) depending on catalyst and potential. Using a produc­tion rate of 15 J ml−1 day−1 of methane (190 nmol ml−1 day−1), the en­tire microbially accessi­ble oilfield (2%) has a ca­pacity of 3.6 mil­lion MBtu per year. Mi­crobes would theoretical­ly consume 1 TWh per year for 3.6 mil­lion MBtu meth­ane pro­duction if there were no losses and elec­trical power is translate­d into methane 1-to-1. A power genera­tor of 121 MW would be suffi­cient to supply the entire oil­field at these rates. However, all Ger­man off-shore wind­farms produce 7,000 MW mean­ing that only 3% off-peak power can be cap­tured by our ex­ample oilfield. There­fore, the catalytic sur­face and activity must be in­creased to accel­erate methane conversion rates.

Since methanogens produce methane from hydrogen, not only the 2% porespace big enough for cells can be used resulting in an increased catalytic surface to nearly 60%. A hydrogen cata­lyst needs to be found that does not out-pace methanogen growth to keep the reservoir pH within the limits of 6-8 re­quired for methanogen growth. This hydrogen catalyst must be cheap and render an oilfield electrically conductive. A chemical formulation that mimics microbial hydrogen catalysis could be used. It has the potential to turn a non-conductive and non-catalytic oilfield into a con­ductive hydrogen catalyst sufficient to sustain methane produc­tion needed to store all of Germany’s electricity produced by off-shore wind­farms. This catalyst is solu­ble in water when inactive. To become active, it coats mineral surfaces by precipitation that can be triggered by indigenous microbes or by electrical polarization. The investment would be $2.3 mil­lion per MW storage capaci­ty ($16 bil­lion for the entire 7,000 MW). Due to microbial growth, the cat­alytic activity of the system improves dur­ing operation and there is no need for the second component if an immediate production is not crucial. The investments made on the cathode side would then be as low as $600 per MW ($4.2 million for 7,000 MW).

Anodes

As the cathodic side of the reaction can be excluded as limiting factor, the anode needs to be de­signed. Several commercially available anodes such as mixed metal oxides (up to 750 A m−2) with platinum on carbon black or niobium anodes (Pt/C, 5-10 kA m−2) could be used. Anodes based on platinum are the most cost-efficient material available on the market. Invest­ments made for Pt/C (10%, 6 mg cm−2) anodes will amount to $50,000 per MW ($350 million for 7,000 MW). How­ever, the exact amount of Pt needed for the reaction still needs to be evaluated in an experiment be­cause the corrosion rate at 2 V cell voltage is unknown. An often cited value for the life­time of fuel cells is 5,000 hours and is used here to determine the costs per kWh. For 5,000 hours life­time, the costs per kWh will be at the targeted limit of $0.01 but may be well below that because Pt/C anodes can be re­cycled and the Pt load may be reduced to 3 mg cm−2 (5%). Alternatively, steel anodes (SS316, 2.5 kA m−2, $54,000 per MW) can be used but it is unclear when steel anodes fail to elec­trolyze. In conclusion, the anodic side is the cost-driving factor. Hope­fully, better water splitting anodes will lower these costs in future.

Cost estimation summary

Windfarms

Already in place

CO2 injection

Already occurred

Natural gas capturing equipment

Already in place

Microbial seed

Wastewater from oil rig

Cathode costs

$600 MW1

Anode costs

$50,000 MW1

Electrolyte (seawater)

Free

Total (>5,000 hours anode lifespan)

<$0.01 kWh1

Energy and conversion efficiencies

The whole cell voltage for microbial power-to-gas reactions varies from 0.6 to 2.0 V, depending on ca­thodic rates, anodic corrosion and the presence of a membrane. Higher voltages will accelerate an­ode corrosion, again, making anodes the limiting factor. As the voltage decreases, methane production rates become slower but also more efficient. The voltage also depends on the pH of the oil­field. An oil­field that underwent CO2 injection as enhanced recovery method will have a low pH, provid­ing better condi­tions for hydrogen production but not for microbial growth and must be neutralized using seawa­ter. As stated above, the oilfield, being the cathode, is not limiting the the sys­tem. The use of Pt/C an­odes eliminates the overpotential problem on the anode side. Hence, we can assume an ideal system that splits water at 1.23 V. However, the voltage is often 2 V due to anode and cathode overpotentials. Optimized cul­tures and cathodes produce about 190 nmol ml−1 day−1 methane which equals 0.15 J ml−1 day−1 using the energy of combustion of 0.8 MJ mol−1. The same electrolysis cell consumes 0.2 mW at a cell voltage of 2 V which equals 0.17 J ml−1 day−1 and the resulting energy effi­ciency is 91%. The anodes can be simple carbon brushes and the two cham­bers of the cell are separated by a Nafion™ membrane. The system can still be optimized by using Pt/C anodes and by avoiding mem­branes.

The overall electricity-methane-electricity efficiency also depends on the consumption side efficiency where methane is used in com­bustion engines and gas fired power plants. Such power plants fre­quently operate at efficiencies of 40- 60%. Assuming a reasonable power efficiency of 80% (see above), the overall electrical power recov­ery using gas fired power plants will be up to 50%. Besides the high efficiency of gas fired power plants, they are also easy to build and therefore contribute the a better power grid efficiency. Coal fired power plants can be upgraded to gas fired power plants.

Experimental approach

The conversion efficiencies of charge (Coulombs) transported across the circuit are usually between 70-100% in these systems depending on the electrode material⁠. Another efficien­cy limitation could arise from mass transport inhibition. Mass transport can be improved by pump­ing electrolyte adding more costs for pumping which still have to be de­termined. However, since most oil­fields undergo seawater injection for enhanced oil recovery the addi­tional cost may be negligi­ble. The total efficiency has yet to be determined in scale-up experiments and will depend on the fac­tors men­tioned above.

The reactor simulates oilfield conditions using sand as filling material under continuous flow of electrolyte.

Controlling the pH is crucial. Alkaline pHs significantly impede hydrogen pro­duction and therefore methanogenesis. This can be addressed by a software that monitors the pH and adjusts the po­tential accordingly. Addition of acids is not desired as this drives the costs. The software can also act as potentiostat that then fully controls the methane production process. To test the process under more realistic conditions, a drill core from an oilfield must be obtained.

Results show methane production in the simulation reactor. The appearance of methane in the anode compartment was a result of flow from the cathode to the anode, carrying produced methane with it.

Return of investment of the microbial power-to-gas process

The the microbial power-to-gas process in unproductive oilfields is economically superior to all other storage strategies because of the low start-up and operating costs. This is achieved because the ma­jor investments are the installation of oil- and gas production equipment and renewable power plants which are already in place as a precondition. These investments break even in a short amount of time.

But how can the microbial Power-to-Gas process accelerate the return of investment in renewable en­ergy? Only 8 out of 28 active off-shore windfarms reported their investment costs. These 8 produce roughly half the overall power of 1,600 MW corresponding to $7 billion. While the maximum production of an oilfield with unlimited supply of elec­tricity would yield hypothetical 3.6 million MBtu natural gas per year resulting a return of $13 million per year the real production is limited by off-peak power gener­ated by re­newable energy production. Assuming that the maximum annual methane production corresponds to 10% excess electrical power, $15 million per year can by gener­ated by selling 4.3 million MBtu meth­ane per year on the market. These are $15 million that are not lost during off-peak shutdowns. Clearly, this conservative estimate can help to compensate the invest­ment in renewable energy earlier. It also decreases the investment risk because the investment calcu­lations for new wind farms can be made on a more reliable basis.

In the example using all German windfarms (7,000 MW) this compensation roughly doubles. Using the $60 million generated by methane sales per year, the investment of $4 million for the cathodic cata­lyst and the $36 million for the Pt/C anodes are compensated for within less than a year. No other invest­ments are required because the target oilfield already produced oil and gas and all necessary installa­tion are in working condition. The target oilfield is swept using seawater as sec­ondary extraction method. Electrical installations are in place for cathodic protection of production equipment in order to prevent microbial corrosion, which, however, may need to be upgraded to pass the now higher power densities. Moreover, CO2 is used from CO2 injection as tertiary enhanced oil re­covery method. Only the pH may then need to be adjusted to sustain life by sweeping with seawater.

And this is not the end of oilfield storage capacity. In theory, an oilfield can store the entire amount of renewable energy produced in one year globally, allowing more than enough head room for future development and CO2 sequestration.